Measuring & Testing

Measure and test efficiently with ELABO

Reliable high-voltage testing of breathing equipment

At a glance

Mobile test system with the following components:

  • Elution® Software
  • Test computer
  • Switching panel for multiple HV test points
  • High voltage test

Description

The ELABO test system is used for high-voltage testing of breathing equipment according to EN60601. The test system consists of a test mobile, which includes the following devices: Test computer, HV unit and switching panel as well as a reserve plug-in unit. At the test mobile, the data of the devices to be tested are read in directly by means of a manual barcode scanner. The use of the Elution® Software allows a retrofittable interface to your ERP system – for later, direct transfer of the test results to the production order.

Testing of medical devices

At a glance

  • Elution® Software
  • Protective conductor resistance measurement
  • Insulation resistance measurement
  • High voltage testing
  • Leakage current testing
  • Electrical Power Measurement
  • Light testing
  • Visual tests

Description

The test station is used for testing medical technology devices (EN60601). The devices are tested for electrical safety (PE, ISO, HV, LC), power consumption, interface communication and functionality of the active components in a partially/fully automated manner. Additionally, a measurement and evaluation of the light data of the test object is performed via an integrating sphere. At the test station, the data of the devices under test are read in directly by means of a manual barcode scanner. This identifies the DUT type and the test program loads the associated test plan data and is ready to start. Mains contacting is carried out manually by the operator. In the test bench, the protective conductor test, insulation resistance measurement, high voltage test, leakage current test, electrical power measurement, light test, visual tests are performed. All generated measured values, test plan data and user data are stored and managed centrally on the system computer. The operator can adjust the test system to his ergonomic needs by means of electrical height adjustment.

Safety and performance testing of electrical refrigeration equipment

At a glance

  • Elution® Software

  • Protective conductor resistance measurement (PE)

  • Insulation resistance measurement (IS)

  • Leakage current measurement (LC)

  • Dielectric strength (HV)

  • Functional test (voltage, current and power measurement)

Description

The test system is used for electrical safety and performance testing of electrical refrigeration devices with AC or DC supply. The connection panel with sockets and connectors is used for contacting the test object. At the beginning a manual electrical connection of the test object with the test system is carried out by the operator (plug in the connection field). Control and monitoring is performed via the integrated system computer using the Elution® Software. Similar test steps, e.g. PE, can be present several times with different limit values in the test plan. The structure of the test sequence is variable and can be individually adapted to the test object and the activities required for the test. The Elution® Software provides convenient functions for managing the test plans and measured values. In addition, a powerful statistics module is integrated, which allows an exact evaluation of the test data. The measured values are stored in a local SQL-Express database.

Fully automatic testing of dielectric strength, protective earth connection and power measurement of built-in refrigerators

At a glance

  • Protective conductor test
  • High voltage testing
  • Power measurement
  • Central SQL database
  • Automatic contacting modules
  • Connection to the customer's BDE control system
  • Automated positioning of test fixtures
  • Rationalization of the test sequence
  • One test base station for all product groups
  • Automatic adaptation to product sizes
  • Automatic contacting
  • RFID / 2D barcode test data recognition

Description

The test system automatically checks the dielectric strength (HV), the protective earth resistance (PE) and the power consumption of the appliances in the refrigerators. The devices to be tested are transported to the test position on pallets via a belt system and placed and fixed there via a pneumatic device. The belt system reports "devices in position" to the ELABO test system via a digital interface and scans the type code (device barcode) of the device to be tested. The type data is reported to the PDA control system. The customer PDA system transfers the relevant test data to the Elution® Software for device-specific testing. In the test portal, the automatic device contacting is carried out via the axis system (mains contacting and PE contacting). After the test has been completed, the test data is automatically reported back to the PDA system. The system rack contains all measuring devices, the system PC, the switching of the test voltages and test currents, and the control of the automatic contacting for mains contacting and PE test adapters.

Automated test system for testing ovens

At a glance

  • Two industrial robots with integrated tools for automated
    • Air flow measurement,
    • PE measurement at any number of positions,
    • Print image inspection and evaluation via an integrated camera system,
    • Testing the functionality of all LEDs on the display,
    • Testing the touch functionality,
    • Rotary selector check for detection of stiff rotary selectors and
    • Helligkeitsmessung der Backofenlampe
    • brightness measurement of the oven lamp.
  • Elution® Software

Description

The system is used for automated testing of baking ovens. By reading out the article number, the system automatically recognizes which product it is and adjusts the test accordingly. Thus, a large number of orifice plates, rotary selectors and appliance heights can be covered by the same system.
The system is controlled by the Elution® factory software.

Safety and functional testing of electric hobs

At a glance

  • PE conductor test: 10-32 A, 0-1,200 Ohm

  • High voltage testing: 100-5000 V AC/DC

  • Short circuit test: 12 V AC

  • Performance measurement: 2-4000 W per phase

  • Pot Simulation

  • Heating circuit detection via current flow detection

  • Button testing via pneumatic cylinder

  • Visual inspections by operating personnel

  • Cycle time: approx. 35-120 Sec. (depending on variant)

Description

The test system is used for safety and functional testing of a wide variety of electric hobs. Therefore, the test portal can be manually changed over to the type of hob to be tested. The system rack contains all measuring devices, the system PC, the switching on and off of the test voltages and test currents, as well as the control of the automatic contacting, the pot simulators and the operating device of the cooktop. A transformer unit is installed in the system rack to perform the HV hot test.In the test portal, the automated contacting and testing of the hob takes place. The operator manually pushes the hob into the test area, stoppers are used to fix the hob in the test position. An automatic barcode scanner scans the type label of the hob and automatically starts the defined test sequence.
The test cells have also been optimized for high product variance.

Semi-automated functional testing and flashing of oven panels

At a glance

  • Elution® Software
  • Flashing/programming the software on the test object
  • Touch testing by robot
  • Vision inspection by robots
  • Testing the frequency and volume of a sound signal of the test object
  • Visual inspection of the test object by workers for scratches supported by worker guidance

Description

Three test objects can be placed in each of the two manually operated drawers. The software is then flashed onto the test objects. A robot controlled by the Elution® software checks the touch functionality of the test objects after the drawers are inserted. A camera installed on the robot also checks various colors and symbols on the display of the test objects. Then the frequency and volume of an audio signal is checked.
Finally, the operator, supported by the operator guidance of the Elution® software, checks the test objects for scratches before they can be removed again.
The entire system is controlled by the Elution® factory software.

Manual high voltage test for electricity meters

At a glance

  • High voltage testing up to 10 kV AC and 12 kV DC
  • Two testing chambers

Description

The manually operated sliding system has two testing chambers in which the test objects are contacted via laboratory sockets. Up to six test points per test object are possible. The system is used for high voltage tests up to 10 kV AC and 12 kV DC. It is controlled by the Elution® factory software.

Testing system for heating cables and heating mats

At a glance

Description

The test system has two integrated water tanks for testing heating cables and heating mats. The test objects are manually placed in a loading basket per tank and contacted at the connection boxes. The unit then automatically lowers into the water bath and an insulation resistance and a high-voltage test of the test objects against the surrounding water is performed. While one side of the system is automatically tested, the other side can be loaded. The entire test system is controlled by the Elution® factory software.

Semi-automated circulation system for testing cell contacting systems

At a glance

  • Elution® Software
  • Error-free assembly due to worker guidance
  • Continuity check
  • Insulation resistance test
  • High voltage test
  • Component marking with laser

Description

The semi-automated circulation system is composed of various stations through which the test object passes on a workpiece carrier via a conveyor belt. The first station is an insertion station where the test object is inserted, scanned and identified by an RFID system. The worker is guided through the assembly process by the Elution® software.
In the following test station the test object is again identified by means of an RFID system. The workpiece carrier is lifted and indexed, the test object is contacted from below via two contacting units. From above, the test object is also contacted via pneumatic contact pins at up to 36 test points. This is followed by a continuity, insulation resistance and high-voltage test.
The third station in the system is a laser station in which the test object is again identified by the RFID system, the workpiece carrier is lifted out and indexed. "Good" tested objects are lasered with a DataMatrixCode. The code is then counter-scanned in order to verify its contents.
A conveyor belt transports the test object to the unloading station. Here the test object is identified one last time by the RFID system. Final assembly activities are performed on "good" tested test objects, supported by the worker guidance of the Elution® software. "Bad" tested test objects are disposed of in a corresponding faulty parts box. 

Simple and optimized assembly of components

At a glance

  • Assembly system with Elution® worker guidance
  • As rotary or linear system
  • Lifting units for individually adjustable ergonomic working height per station
  • Material supply and return via rack systems
  • Pick by Light
  • Individually adapted workpiece carriers
  • Can be combined with other systems such as vision inspection

Description

Mount your assemblies simply and with optimized cycles on an assembly system like this. With the help of the Elution® worker guidance, every employee can easily change the workplace and knows immediately what to do. Reduce the initial difficulties (new employee, new product, ...) to a minimum.
 

Ergonomic programming of refrigerator covers

Components

  • Air-conditioned control cabinet with installation space for an industrial PC 19" 4 RU
  • Ergonomic, electric height adjustment
  • Interchangeable adapter for flexible programming
  • Integrated workplace lighting

Thanks to the continuous, electrical height adjustment and the integrated workplace lighting, the mobile programming station enables ergonomic working all round. The air-conditioned control cabinet protects the industrial PC from overheating.

Simple and fast testing of insulated tools

Components

  • Semi-automatic operator test station
  • SPS controlled test station
  • Tool testing system for insulated tools (screwdrivers, pliers, ...)
  • Magnetic tool holder
  • Hi-pot testing in a water bath

Simple and fast testing of your insulated tools in a water bath. Simple recognition of whether the insulation of the tools is in order by means of hi-pot testing.

 

Simple and fast testing of cable harnesses

Components

  • Semi-automatic operator test station
  • Final testing of cable harnesses
  • Engraving of good parts by laser
  • Ferrite testing
  • Continuity test
  • Hi-pot testing
  • Colour inspection of the cable cores

Simple and fast testing of cable harnesses. After you have connected the plug to one of the two adapters, all tests are carried out and the plug is engraved immediately after good testing.

Greater efficiency with versatile measuring

Components

  • Primus Basic workstation, mobile, with 3 RU top unit
  • Primus One workstation with 3 RU, 6 RU top unit and shelf unit

Simple drive your mobile measuring unit direct to your DUT. This flexibility improves efficiency in your company.
The combination of electrified top units and shelf storage gives you an ideal setup with enough space to file away your documents while simultaneously ensuring you can use the installed measuring instruments.

Better quality by testing with ELABO

Components

  • Elution® software
  • Current/voltage testing
  • Functional testing
  • Hi-pot testing
  • Insulation testing

Test your electrical components or parts with your specific testing methods. This test bench improves your product quality.

Enjoy simple, rapid product testing

Components

  • Fully automated test run
  • Hi-pot testing
  • Pre- and post-burn out
  • Capacitance measurement
  • Surge current testing

Simple, rapid testing of your products for good and bad parts with our in-house developed Elution® package. The software can also be integrated with your ERP system.

 

Consumption and temperature rise measurements with ELABO solutions

Components

  • Elution® software
  • Graphical progress meter
  • Line voltage 80 … 280 V
  • Current measurement 0 … 20 A
  • Voltage measurement 0 … 600 V
  • Output/energy measurement
  • 8-channel winding temperature rise measurement
  • 2-channel water volume measurement
  • Leakage current testing
  • Temperature measurement
  • Motor speed recording
  • Recording of external measurement signals

ELABO advises and assists you in performing consumption and temperature rise measurements for your product.

Simple and versatile supply channel testing with mobile test systems from ELABO

Components

  • Elution® software
  • Hi-pot testing 0 … 5,000 VAC
  • Protective conductor continuity testing 6 VAC/25 A
  • Insulation resistance testing 0 … 35 MΩ
  • Leakage current testing 0 … 10 mA
  • Line voltage 0 … 280 VAC/5 A
  • Current measurement 0 … 5 A
  • Software control, incl. measurement data archiving
  • Dummy testing

The mobile testing systems are in widespread use in medical technology: they offer you a simple, versatile way to test supply channels.

Long-term analysis of electrical appliances

Components

  • Elution® software
  • 3 flexible SC power supplies
  • Current/voltage measurement
  • Output measurement
  • Temperature measurement
  • I-V curve determination
  • Profile sequencer

Perform long-term analysis on your electrical appliances. ELABO’s Elution® software package lets you perform various measurements such as temperature measurements, output measurements or current/voltage measurements. Measurements can also be accessed and controlled in real time.